General Principle and Process of Isolation of Elements
These are naturally occurring chemical substances in the in the earth crust obtainable by mining.
Ores : –
only few minerals are used as sources of that metal. Such minerals are known as ores.
ores are usually contaminated with earthly or undersides materials known as gangue.
The entire scientific and technological process used for isolation of the metal from its ores is known as metallurgy.
Concentration of the ore: –
The removal of earthy and siliceous impurities (i.e. gangue or matrix) from the ores is called concentration of ores.
(i) Hydraulic washing: –
The processes by which lighter earthy particles are free from the heavier ore particles by washing with water.
(ii) Magnetic separation: –
This method of concentration is employed when either the ore or impurities associated with it are magnetic in nature.
(iii) Froth floatation: –
This method is based upon the fact that surface of sulphide ores is preferentially wetted by oils while that of gangue is preferentially wetted by water.
(iv) Leaching: –
This process consists in treating the powdered ore with a suitable reagent which are selectively dissolved the ore but not the impurities.
1) Leaching of Alumina from bauxite: –
ore of aluminum, bauxite usually contain SiO2, iron oxide, Tio2, as impurities .the concentration is carried out by digesting the powdered ore with the concentrated solution of NaOH at 473 to 523 K and 35-36 bar pressure. This way Al2O3 is leached out as sodium aluminates behind.
2) Other Examples: –
In the metallurgy of silver and that of gold , the respective metal is leached with a dilute solution of NaCN or KCN in the presence of air (for O2) from which the metal is obtained later by replacement.
Extraction of crude metal from concentrated Ore :-
1. Conversion of the ore into metallic oxide or de-electronation of ores: –
Metal usually present as hydroxides, carbonates and sulphides depending upon the nature of the minerals present in the ore, the following two present in the ore, the following two methods are used for conversion of ore into their respective oxides.
(a) Calcinations: –
It is the process of converting on ore into is oxide by heating it strongly below its melting point either in absent or limited supply of air during calcinations following change occur
(b) Roasting: –
It is the process of converting an ore into its metallic oxide by heating strongly at temperature insufficient to melt in excess of air. This process is usually used for sulphide ores. Following change occur during roasting.
Thermodynamic principles of metallurgy: –
For any process, Gibbs free energy change (∆G) is given by
(a) Extraction of iron from its oxides –
Oxides ores of iron after concentration through calcinations/ roasting are mixed with limestone and coke and fed into a blast blast-furnace from its top. Here, the oxides is reduced to the metals
(b) Extraction of copper from cuprous oxide: –
Most of the ores are sulphide and some may also contain iron . The sulphide ores are roasted/ melted to give oxides.
(d) Extraction of Aluminum: –
Alumina Al2O3 is mixed with Na3AlF6or CaF2 which lowers the melting point of the mixture and brings conductivity. Fused mixture is electrolyzed. Steel cathode and graphite anode is used. The graphite anode is useful for the reduction of metal, the overall reaction are as follow-
(e) Extraction of copper low grad ores and scraps :-
Copper is extracted by hydro metallurgy from low grade ores it is leached out using acid or bacteria the sol containing Cu2+ is treated with scrape iron or hydrogen.
Oxidation reduction: –
Besides reduction, some extraction are based on oxidation particularly for non-metals. For extraction of chlorine from brine.
The process of purifying the crude metals is called refining. Some methods of refining are as follow.
a) Distillation: –
This is very useful for low boiling metals like zinc and mercury. The impure metals are evaporated to obtain the pure metals as distillate.
b) Liquation: –
In this method a low melting metal like tin can be made to flow on a sloping surface, in this way it is separated from higher melting impurities.
c) Electrolytic refining: –
In this method the impure metal is made to act as anode a strip of some metal in pure form is used as cathode. They are put in a suitable electrolytic bath containing soluble salt of the some metals the more basic metal remains in the solution and the less basic ones go to the anode mud.
d) Zone refining: –
In this method a circular mobile heater is fixed at one end of a rod or the impure metal, as heater more forward, the pure metal crystallises out of the melt and impurities pass on into the adjacent molten zone.
e) Vapour phase refining :-
The crude metals is free from impurities by first converting it into a suitable volatile compound by heating it with specific reagent at a lower temperature and then decomposing the volatile compound at some higher temperature to give the pure metal.
Ex: – (1) Mond Process and (2) van arkel method
The method is based upon the principle that the different components of a mixture are adsorbed to different extents of an adsorbent.